第12章 12.1.1 Inter-switch links ISL有3种方式: ◆ ISL R_RDY Mode : 用于取代Remote Switch ---> portcfgislmode 9,1 ◆ Remote Switch:已被ISL R_RDY Mode取代 ◆ Extended Fabrics 12.1.2 Buffer credit recovery 此功能仅用于8 Gbps switches 只支持长距离的GoldenEye2 and Condor2-based ports的E_Port 此功能不需要配置 12.1.3 Advantages of ISL Trunking ISL Trunking 是b-type 系列交换机上可选组件 需要购买license ISL Trunking 可将4个或8个ISL合并为单个链路 ISL Trunking使用Expansion Port (E_Port) ISL Trunking 使用frame-level 负载均衡 当一个master link offline时,会自动选择新的master link,不会中断传输 Trunk ports: ◇ 必须是E_Ports or EX_Ports ◇ Trunk ports必须运行在相同的速度 ◇ 每个交换机都要安装trunking license ◇ 交换机之间的trunk线缆长度要小于500m Trunk masters: ◇ 用于定义trunk group ◇ 每个trunk group有一个trunk master和几个trunk subordinate link ISL Trunking Telnet commands GUI ---> 选中端口 ---> Enable Trunking 或 Disable Trunking P462---P496 12.1.4 Fabric Interoperability trunking 不支持在FOS和M-EOS之间进行trunk Long distance 在不同的模式下对license有不同需求 ---> portCfgLongDistance L0: 正常值,禁用long distance LE: 10km L0.5 : <25 km L1 : <50km L2 : <100km LD : LS : 12.2 Merging fabrics 通过ISL连接多个SAN,形成一个大的fabric 添加交换机到现有的fabric之前要disable交换机:可避免Domain ID冲突,将交换机disable后接入fabric,再enable,会自动协商Domain ID,并设置有效值 Domain ID用来标识交换机,在fabric中每个交换机的Domain ID必须唯一 ---> switchDisable ---> configure Fabric Manager ---> Tasks → Fabric Management → Fabric Merge Check 合并SAN: 如果两个交换机在合并时有冲突(?),会先offline一个交换机,合并后再online 用ISL连接多台交换机 ISL Trunking增加带宽 13:14 2009-6-29 第13章 Secure Fabric OS是可选组件,需license FOS 6.X不再支持Secure Fabric OS Secure Fabric OS只能用于FOS 5.3及以前版本 Secure Fabric OS使用数字证书 Fabric Manager会自动将交换机密码存储在服务器上(默认) 当disable此功能后,重启client需要再次monitor fabric FM --->Edit --->Preferences --->General --->Persist switch passwords 默认为勾中,即启动此功能 FM ---> Tasks → Switch Management → Set Admin Password 选中多台交换机,更改密码 在status列中:黄色---正在设置新密码 默认时,所有交换机使用HTTP来管理 FM每30分钟更新一次Admin Domain信息,刷新Fabric Data不会更新Admin domain信息 256个Admin domain(0—255) 未看完 11:12 2009-6-30 第14章 Adaptive Networking :优化SAN的一套工具 ◇ Traffic Isolation:支持4G/8G交换机,无需license ◇ Quality of service (QoS) Ingress Rate Limiting:只支持8G交换机,需要license ◇ QoS SID/DID Traffic Prioritization:只支持8G交换机,需要license 14.1 Traffic Isolation 用于控制交换机之间的传输,使用专用的N_port建立一个专用路径来传输数流 Traffic Isolation使用专用的zone, 叫做Traffic Isolation zone (TI zone) 使用F_Port和E_port 14.1.1 Creating a TI zone ---> zone --create -t objtype [-o optlist] name -p “portlist” ---> zone --create -t ti ti_host1 -p "1,29; 1,30; 1,0;2,2;2,5; 4,6; 4,12; 4,13" ---> cfgenable "FabricA_Cfg" 14.1.2 TI zone failover 14.1.3 FSPF routing rules and traffic isolation 所有的传输必须使用低成本的路径All traffic must use the lowest cost path. 未看完 第15章 一些高级功能只能使用CLI Web Tools ---> Performance Monitor 性能监控每30秒更新一次 保存自定义的监控:File → Save Current Canvas Configuration 调用自定义的监控:File → Display Canvas Configurations 基本的性能监控:不需要license Web Tools ---> Performance Graphs → Basic Monitoring ◇ Port Throughput : 选中一个端口,查看端口吞吐量 ◇ Switch Aggregate Throughput: 交换机所有端口总的吞吐量 ◇ Blade Aggregate Throughput:仅对SNA768B和SAN256B有用; 显示某个blade的吞吐量 ◇ Switch Throughput Utilization:显示各端口的吞吐量利用率 ◇ Port Error:显示端口的CRC错误量 ◇ Switch Percent Utilization:类似于Switch Throughput Utilization,但显示的是百分比 ◇ Port Snapshot Error: P655 高级性能监控:需要license ◇ SID/DID Performance:在源ID和目标ID对之间的传输; 要选正确的SID,DID,Switch Port ◇ SCSI Commands: 显示每个交换机端口或端口上指定LUN的读/写命令的数量 ◇ SCSI versus IP Traffic:端口上IP和SCSI传输量的百分比 ◇ ALPA Error: 用在旧的交换机上 P663---P677 15.2.1 End-to-end monitoring 在SID和DID之间的FC frame的传输量 ---> perfAddEEMonitor 15.2.2 Displaying the end-to-end mask of a port 15.2.3 Filter-based monitoring 15.2.4 ISL monitoring 15.2.5 Top Talkers monitoring 15.2.6 Trunk monitoring 15.2.7 Saving and restoring monitoring configuration 一般的监控在WEB TOOLS中用图形方式显示 高级监控需要license,用CLI (未看) 15:58 2009-6-29 第16章 确保SAN健康和排错 16.1 SAN Health SAN Health :此工具用于管理和优化SAN 两种机制: back-end reporting processor front-end data collection agent 前端收集数据 后端处理 下载并安装SAN Health 将收集到的数据通过SAN Health发送到Brocade Wet Site,24小时内会收到结果 收到的结果是2个文件: 一个visio连接图 16.2 Error logs 3种错误日志: ◇ TraceDump: 复制内存到一个文件中 ◇ RASLOG: 包含交换机的debug数据 ◇ supportShow: 交换机的状态和配置信息 16.2.1 Capturing a trace dump …… P700 FM → Tasks → Capture Technical Support Information --->supportShow --->supportSave 16.2.3 General device health FM → Tasks → Device Management and Troubleshooting → Device Connectivity Trouble Shooting 16.2.4 Trace route 路由路径信息 FM → Tasks → Device Management and Troubleshooting → Trace Route 16.2.5 Fabric merge 检查fabric合并时是否有冲突 FM → Tasks → Fabric Management → Fabric Merge Check 16.3 Port Fencing Fabric Operating System v6.1 (Fabric OS) adds a new feature called Port Fencing, which disables a port automatically when it is operating outside the bounds of normal operation. E, F, and FL port types are port classes supported by port fencing, and we can enable the port fencing for these port classes only. ---> fwconfigure ---> switchShow 16.4 Command output enhancement ---> switchshow |more 16.4.1 Basic troubleshooting commands基本的排错命令 chassisShow diagShow errDump errshow fabStatsShow fanShow fcPing islShow portCfgShow portErrShow portLogShow portShow portStatsShow psShow supportshow switchShow topologyShow ---> help <command name> 9:24 2009-6-30 P28 在Web Tools中可查看,升级FOS P29 Brocade Access Gateway Administrator's Guide P31 fabric OS native fabirc OS open M-EOS native M-EOS open mode P32/33 P32 CHAPTER 2 P45 对本章内容没能深入了解 是否是讲用 SAN768B (Brocade DCX Backbon)来构建存储虚拟化??? CHAPTER 3 P56 P57 用4/8个端口做ISL Trunk Group,负载匀衡 P70 P73 P75 P80 P81 P82 P86 SAN256B CHAPTER 4 Access Gateway FC4-16IP------16个iSCSI端口 ??? FICON Fabric OS的升级,降级,备份 CHAPTER 6 设置交换机时间日期 --->date “MMDDhhmmYY” P122 SAN768B的logical switch SW0上没有默认IP P125 用ipAddrSet设置交换机IP时 Fibre Channel IP Address [none]: P128 ---> ipAddrSet –sw 0 P130 在用telnet连接到交换机时,命令是否区分大小写 ??? CHAPTER 8 Web Tools需要JAV 1.6, IE 7 CHAPTER 11 P423 P425 --->最大zoning database是多大??? P438 P450 CHAPTER 12 在实际应用中,如果2个独立的SAN合并为一个大的fabric,可能会有一些配置冲突,如何解决这些冲突,未看明白 |
联系客服