Fiberglass sculpture production

Fiberglass sculpture made by hand laying method. Before the production will be based on the shape of the sculpture characteristics, from the ease of forming and stripping point of view, you can split the mold into a number of units to replace. Thus forming the unit products, and then combine them into a whole. Finally, the overall processing and painting products, a glass steel sculpture on the production is completed. 2.2.1 mold making

Mold making is the key to FRP molding. Fiberglass sculpture mold production often use gypsum material, but the gypsum material strength is low, easy to place a long time to deformation. This article describes a better FRP sculpture mold making method, which is made of silicone rubber and glass fiber reinforced plastic mold method. The following are the same as the "

Silicone rubber material used before the fluid state, mobility and filling is good. After the preparation of the reaction by the formation of rubber elastomer, can have a greater elastic deformation, the original mold of water to its cross-linked to reflect no effect. After the cross-linked silicone rubber seal is good, and the original mold and fiberglass are not bonded. Use it to do Fiberglass sculpture mold surface layer of material, both high-quality copy of the shape of the work, but also to ensure smooth stripping. However, the silicone rubber cross-linked body is easily deformed, and when used as a mold, a support carrier is required. Can be used to facilitate the characteristics of FRP, used as a carrier material of the mold. The following are the same as the "

The specific mold making method is: the preparation of a good silicone rubber painted several times in the original mold, silicone rubber layer should be more than 1mm. After the silicone rubber cross-linked, the silicone rubber and then the thickness of about 3mm glass fiber reinforced plastic layer. After the glass fiber is cured, the whole mold is cut along the divided unit block, and the glass fiber layer and the silicone rubber layer are cut at the same time. The connection ribs are made between the unit blocks, and the groove should be set at the connection ribs to ensure that the unit block molds are integrally formed by connecting the ribs. After the above work is completed, the fiberglass unit block stripping, and then take off the silicone rubber layer, take off the silicone rubber block immediately back into the glass fiber reinforced plastic module. The following are the same as the "

FRP sculpture with hand laying method, the production should be designed before the molding line. From the end of the sculpture to start a combination of part of the mold after the paste system products. Until the former part of the curing and then combined mold, continue paste system products. The mold unit block is combined as much as possible at the time of facilitating the forming operation. So repeated, and finally set aside a unit block, the unit block preformed glue to the overall sculpture. Fiberglass sculpture (Xiao Liu resin online reprint) similar to the animal's horns, legs, tail and so difficult to use the above method

Of the part, you can use the corresponding metal material made of the general shape, and then in the metal material on the production of glass fiber reinforced plastic, through the grinding method to trim out. The following are the same as the "Sculpture surface is generally more complex, in the process should be special treatment. Fiberglass mats are difficult to lay where they should be filled with resin containing short fibers, and then lay the glass fiber chopped mat and square cloth. Sculpture surface layer with resin putty in the glass fiber length to 10mm is appropriate,

sculpture surface with resin putty Matching material Polyester resin Glass fiber CaCO3 Filler Pigment Peroxylated methyl ethyl ketone Naphthalene cobalt amount 1002010022-40.5-4 Fiberglass sculpture in an important issue is the structural enhancement, reinforced materials generally use metal profiles, with metal profiles Welding into a carving (Xiao Liu resin online reprint) plastic skeleton. In the molding production, the metal The following are the same as the "

Skeleton gradually buried in the sculpture. In order to improve the rigidity and strength of FRP sculpture, increase its service life, and finally through the metal frame to install FRP sculpture assembly mold → fill the surface putty → laying chopped mat → laying grid → buried skeleton → final product stripping 2 .3 post-processing

Fiberglass sculpture on the one hand after finishing the demolition of the product after the partial defects, more importantly, the production of surface effects. Often used in the surface effect is imitation copper and imitation bronze, the key is to prepare color paste. Material molybdenum chromium phthalocyanine blue phthalocyanine green dibutyl copper alloy powder content 550.30.7240200 material chromium yellow phthalocyanine blue molybdenum chromium red dibutyl copper powder amount 620.351803003 concluding remarks

Made of glass fiber reinforced plastic sculpture, bright color, smooth lines, handsome in appearance, easy to install. Can be made into imitation gold, imitation copper, imitation stone and other surface effects, thus the performance of modern and sense of the times. In the production of small support, dynamic and strong sculpture, with other materials can not match the advantages. An excellent glass steel sculpture from the design, mold, forming, post-processing, etc., by ensuring the quality of each link to be achieved.

From：sculpture

http://blog.sina.com.cn/s/blog_16e31905b0102xrn2.html

http://blog.sina.com.cn/s/blog_16e31905b0102xruj.html